Home  /  Research compounds  /  Retatrutide Research Peptide
Compound data file · research use only

Retatrutide Research Peptide — Purity, COA & Batch Data

Retatrutide is a 39-residue synthetic peptide carrying a C20 fatty diacid side chain. The chain makes it the most hydrophobic compound in this set, and the side chain makes its mass hard to state as a single number — which is exactly why the certificate has to say which form was measured.

≈ 4,731.4free peptide
39 aachain length
2381089-83-2CAS

Published molecular weights for the retatrutide peptide vary by several hundred daltons between suppliers. The variation is not sloppiness in every case: the free peptide, the trifluoroacetate salt and the formulated material are different things, and the number quoted usually depends on which one was measured.

Compound identity

Backbone length 39 amino acids, synthetic, with a C20 fatty diacid side chain
Modification C20 diacid moiety; this is what makes the molecule amphiphilic
Molecular weight ≈ 4,731.4 g/mol for the free peptide; salt forms report higher
CAS registry 2381089-83-2
Receptor profile GIP, GLP-1 and glucagon receptor agonist — a three-receptor research tool
Supplied form Lyophilised white to off-white powder
Solubility Limited in plain water; needs pH control or a small amount of organic co-solvent
Storage (powder) −20 °C, desiccated, protected from light

The mass has a form attached to it. A certificate that states a mass without stating which form was measured is not comparable with any other certificate. Ask for the form, then compare.

How Retatrutide identity is confirmed lot by lot

Because the retatrutide sequence is 39 residues with a lipophilic side chain, the electrospray spectrum is a broad charge envelope, so the deconvoluted mass is the only usable figure. The certificate should state the deconvolution, the form measured, and the expected range rather than a single integer, because salt and residual solvent move the measured value.

The second check is the side chain. A 39-residue backbone without the C20 diacid is a different molecule with a much lower mass; the two are sometimes discussed interchangeably in supplier listings but they are not the same product. Where a lot is described as retatrutide, the certificate mass should be consistent with the modified sequence.

  • Deconvoluted mass stated with the form measured.
  • Side chain presence consistent with the stated mass.
  • HPLC purity with the trace, on a gradient that resolves the lipophilic variant.
  • Residual solvent or counter-ion acknowledged where it affects the figure.

Purity, impurities and what the COA should show

Retatrutide purity is limited by aggregation and by lipophilic variants rather than by oxidation. Aggregates are the harder problem because they may not appear as a separate peak at all on a standard reverse-phase run.

Aggregation and lipophilic variants

Aggregated material can elute as a broadened main peak rather than a distinct impurity, which inflates a purity figure without any peak being added. A method that includes a size-based check, or at least a stated run time long enough to show the broadening, gives a buyer something to judge.

Residual solvents and salts

Purification of a lipophilic peptide uses solvents that can remain at low levels, and the salt form changes the weighed mass. Both belong on the certificate where the lot is sold by mass, because both change what a balance reading means.

  • Purity by HPLC with the chromatogram and run time.
  • Deconvoluted mass and form stated together.
  • Aggregation or peak shape noted where visible.
  • Residual solvent and counter-ion acknowledged.
  • Storage instruction matching the supplied form.

Reconstitution and storage for laboratory stock

Retatrutide does not go into plain water easily. Wet the powder with the full volume, allow time, and use a slightly alkaline buffer or a small fraction of organic co-solvent where a higher concentration is needed. Heating is not a solution to a solubility problem with a lipophilic peptide.

Solvent Neutral to slightly alkaline buffer; small amounts of acetonitrile where needed
Working stock 1–2 mg/mL; higher concentrations tend to aggregate
pH 7–8; keep away from strong acid, which drives aggregation
Aliquoting Single-use aliquots at −20 °C, frozen immediately
Light Amber vial; the tryptophan and tyrosine residues are the sensitive part
Powder storage −20 °C, desiccated; equilibrate before opening

Do not heat a lipophilic peptide into solution.

Ordering Retatrutide: pack sizes and batch documents

The retatrutide peptide spans the widest range in the catalogue, from a 5 mg kit up to a 100 mg kit. Each fill is a separate lot with its own Retatrutide COA; a quotation for several fills returns several certificate numbers.

Pack Format Price
5 mg × 10 vials 10-vial kit $65
10 mg × 10 vials 10-vial kit $100
15 mg × 10 vials 10-vial kit $140
20 mg × 10 vials 10-vial kit $170
30 mg × 10 vials 10-vial kit $240
40 mg × 10 vials 10-vial kit $320
50 mg × 10 vials 10-vial kit $370
60 mg × 10 vials 10-vial kit $409
100 mg × 10 vials 10-vial kit $600

A retatrutide supplier who quotes a mass without stating the form has measured something you cannot compare. Prices are per kit at the time of writing and are confirmed on the product page. For mixed lines, custom fills and export documents see bulk research peptides.

Need the certificate with the form stated?

Send the fill you are evaluating. We return the deconvoluted mass, the form measured and the certificate for that lot.

VIEW RETATRUTIDE